High-pressure Variable Vane Pumps VHP series

Welcome to "Saar Hydraulic", your one-stop hydraulics resource.

Features: high pressure variable vane pump HVP in the "axis backlash compensation" high rpm even, stable performance and high efficiency. high pressure variable vane pump HVP's "eccentric plunger" fast responsiveness, start, stop, load rotation, quick action. high pressure variable vane pump pressure adjustment HVP easy, high stability, fast response. the high-pressure variable vane pump HVP easy assembly, composed of direct motor motor pump combination. MODEL NUMBER DESIGNATON VHP──F──40──A3 ----T ① ② ③ ④ ⑥ ① Serial Nunber② Assemble model L: Foot Type F: Frange Type ③ Delivery capacity ④ Range of Adjusting A1: 15-35kg/cm² A2: 35-70kg/cm² A3: 70-105kg/cm² A4: 105-140kg/cm² Instructions of usage:1, the direction of rotation: clockwise high-pressure variable vane pump HVP (viewed from shaft end) as standard, only this turn. HVP high pressure variable vane pump direction of rotation can be instantly recognized the starter motor to check.2, hydraulic oil: 7MPa the following, the use of high-pressure variable vane pump HVP viscosity at 40 ℃ 20 ~ 50cSt (ISOVG32) hydraulic oil. 7MPa above, the use of high-pressure variable vane pump HVP viscosity at 40 ℃ 30 ~ 68cSt (ISOVG46, VG68) hydraulic oil.3, the drain line pressure: high pressure variable vane pump HVP the drain line must be plugged directly into the oil tank under the surface, and the resulting back pressure piping, please remain at 0.03MPa or less.4, the working oil: high-pressure variable vane pump HVP continuous operation in the use of a temperature of 15 ~ 60 ℃.5, Concentric mate: the high-pressure variable vane pump and motor shaft HVP's eccentric error of 0.05mm, the angle error is 1 °.6, the suction pressure: the pressure variable vane pump suction port HVP pressure-0.03MPa ~ 0.03MPa.7, the displacement adjustment: displacement adjustment, the first relaxation in the high-pressure variable vane pump HVP adjustment nut, then rotate the high-pressure variable vane pump HVP adjustment bolt, turn right to reduce traffic, while the left has increased, the adjustment is completed, Please tighten the nut.8, the pressure adjustment: left (counterclockwise) Pressure adjusting screw, so that the output pressure is reduced, turn right (clockwise) is increased, the adjustment is completed, please tighten the nut.9, the new machine operation: the new machine starts running, you should state in the absence of stress repeatedly starter motors, in order to discharge the high-pressure variable vane pump HVP and suction pipe in the air, in order to ensure the exclusion of air within the system can be no-load state in continuous operation for 10 minutes. . Specificatioins:
vane pumps High-pressure Variable Vane Pumps VHP series
Double vane pump works: it consists of stator, rotor, blade and oil pan and other components. The inner wall of the stator is approximately elliptical. The blade is mounted in the radial groove of the rotor and slides along the groove, and the rotor is mounted concentrically with the stator. When the rotor is rotated, the blade is pressed against the inner surface of the stator under the action of centrifugal force, and is forced to reciprocate in the rotor tank with the change of the inner surface curve of the stator, and the sealing working chamber between adjacent two blades is enlarged and shrunk Variety. When the blade is slid from a small radius arc to a large radius arc, the sealed working chamber gradually increases to form a local vacuum, and the oil in the tank is sucked through the oil suction chamber through the oil pan; Rotate the rotor every week, the blade in the tank to slip back and forth 2 times to complete the 2 oil and 2 times the pressure oil, and the pressure generated by the radial force is balanced, so called double acting, also known as balanced.
Single acting vane pump works: mainly by the stator, rotor, blade and oil pan and other components. The inner surface of the stator is a cylindrical shape, the rotor is eccentrically mounted in the stator, that is, an eccentric e, the blade is mounted in the rotor radial chute and slid radially within the slot. Rotor rotation, the centrifugal force and the role of the root pressure of the blade under the action of the blade close to the inner surface of the stator, so that between the two adjacent leaves to form a sealed working chamber. In one side, the blade gradually extended, sealed working chamber gradually increased, the formation of local vacuum, the formation of oil; the other hand, the other side, the formation of oil. Rotate each turn a week, the blade in the chute reciprocating slip 1 times to complete a suction oil pressure. Oil pressure generated by the radial force is not balanced, so called single acting, also known as unbalanced vane pump.
Vane Pumps
Power never sounds better than when it’s quiet—that’s why Eaton fixed displacement vane pumps with low-noise characteristics are an excellent choice for a broad range of mobile and industrial applications. Featuring modular designs for flexible displacement, mounting and port options, as well as cartridge kits engineered for easy interchangeability and repair, Eaton vane pumps excel globally in molding, material handling, construction, manufacturing and automotive industries

vane pumps High-pressure Variable Vane Pumps VHP series

MODEL	MAXPRESSUREkg/cm2	OUTPUT FLOWAT 3.5kg/cm21800 r.p.m.l/min	PORTS SIZE			SPEED r.p.m		WEIIGHT (kg)
			OUT	IN	DR	MIN	MAX	FOOTTYPE	FLANGETYPE
VHP-20	140	20	1/2”	3/4”	3/8”	800	1800	12.5	9.5
VHP-26	140	26
VHP-30	140	30
VHP-40	105	40
VHP-54	140	54	3/4”	1”	3/8”	800	1800	35	25
VHP-70	105	70
VHP-86	105	86